Solved! 2011 BMW Z4 E89 rear axis sensor near its low limit

Car model and year: 2011 BMW Z4 E89 Problem and BMW scanner to use: the rear axis sensor is very near its low limit. Therefore my headlights are not raising to the proper operating height. When I start the car the lights dip and then return to the default low position. Checked it out with BMW INPA and…

Published

Modify VCDS VAGCOM Cable for BMW INPA

Here, you will get answers to questions below: It is possible to use an “old” vcds or vagcom kkl cabel and use it for newer bmw (2004-2011) with the software inpa?Only short the Pin 7&8 from my vcds cable, and use it for bmw? This is a 100% compatible interface and the explanation + schematics…

Published

BMW coding tool update SP-DATEN files guide

The BMW Coding Tool 2.50 allows you to update your SP-DATEN (Data files) automatically instead of manually installing the files by copy and pasting files. It will automatically update the files that require replacing and skip the files that you don’t need! Related Products: BMW Tools Software Package (can be downloaded free here) INPA K+DCAN USB…

Published

How to reset BWM E60 automatic transmission with INPA

BWM E60 automatic transmission reset and relearn by using BMW INPA K+DCAN cable. It is a reset method of learning function. Especially when there is something wrong with a large displacement car There seems to be improvement in some cases. (Physical breakdown is excluded) Launch INPA and select GS 19 Select F6 Reset complete with F3 www.obdii365.com

Published

Code BMW M3 cluster, desolder eeprom, write VIN etc

I’ve done an BMW M3 DCT cluster swap into a 335i properly. Desoldered eeprom, written vin, code the cluster, re-calibrate the dials. Disclaimer: You are at your risk. Many thanks to “vtl” in bimmer post forum. Ncs Expert software doesn’t let you code the cluster unless the VIN matches. You will need to remove the…

Published

Reset MW E60 2006 LCM module via Ediabas

Here is the knowledge about LCM and instruction on how to reset LCM module by using BMW ICOM A2 EDIABAS software. The Light Control Module (LCM) is an important component of a vehicle because it controls all of the car’s lights, as well as the horn function.   What functions are controlled by the LCM? LCM controls…

Published

BMW INPA Ediabas Windows 7 64bit Installtion

Many people are seeking INPA/Ediabas Windows 7 64-bit installation guide. Here you can download free INPA 5.02 and Ediabas 6.4.7 and check the installation guide step-by-step.   Free Download INPA 5.02 and Ediabas 6.4.7 Software   Installation: Step 1: Install software setup Open the DVD and go to the Program installation folder. Rightclick on setup.exe and select Properties. And go…

Published

Swap and code BMW N54 Injector with INPA

N54 Injector Swap & Coding Diy!   Here is a little DIY tutorial on how to swap and code BMW N54 injector at lowest cost. INJECTOR PART# 13537585261 DECOUPLING ELEMENT PART# 13537564751 USB FOR CODING: BMW INPA K+DCAN USB Interface “You are on your own risk“ Anyway… —————————————- I started getting some hesitation/stumble on low rpm’s…

Published

BMW INPA fails to calibrate steering angle sensor

Some BMW INPA K+DCAN OBD2 cable holders reported that when trying to calibrate LWS for BMW, the INPA software reports an error message and fails to reset steering angle sensor.   Error message: “Calibration steering angle only with steering wheel balancer!!”   Model tested example: BMW 3 series E46 320D 2005   Possible reason: BMW…

Published