Read Write VAG DSG DQ200 DQ250 DQ500 with KTMFLASH

KTMFlASH ECU flasher supports VAG DQ200 DQ250 DQ500 VL381 DL501 Direct-shift gearbox Transmission read and write via OBD or boot mode.

Type: DSG and CVT transsmision
Mode:
OBD mode: ECU remap
Boot mode: ECU Repair (W/R EEPROM)
via OBD:
DQ200 (0AM) Write/Calibrate
DQ250C (02E) Read/Write/Calibrate
DQ250E/F (02E) Write/Calibrate
DQ200MQB/G2 (0CW) Write/Calibrate
DQ250MQB (0D9) Write/Calibrate
VL300/V30 (01J/0AN)Write/Calibrate
VL381 (0AW) Write/Calibrate
DL501/G2 (0B5) Write/Calibrate
DQ500 (0BH/0BT) Read/Write/Calibrate
Boot mode:
DQ200/MQB/G2 Boot (MICRO) Read/Write/Calibrate
DQ200/MQB/G2 Boot (EEPROM) Read/Write
DQ250E/F/MQB Boot (MICRO) Read/Write/Calibrate
DQ250E/F/MQB Boot (EEPROM) Read/Write
VL300/V30 BSL (FLASH) Read/Write/Calibrate (open dsg computer)
VL300/V30 BSL (EEPROM)Read/Write/Calibrate (open dsg computer)
VL381 Boot (MICRO) Read/Write/Calibrate
VL381 Boot (EEPROM) Read/Write
DL501/G2 Boot (MICRO)Read/Write/Calibrate
DL501/G2 Boot (EEPROM) Read/Write
KTM Flash workable DSG list:
1) DQ200 – BOOT – ALL,  OBD –ALL, except K-Line 0AM
2) DQ250 – BOOT – E/F/MQB , OBD – All
3) DQ500 – 0BT/0BH (NOT 0DL!) Only read/write via OBD
4) VL300/V30 – BSL – All, OBD –except KW1281
5) VL381 – ALL
6) DL501 -ALL
Operation tips:
OBD Mode:
If you have operational interruption issue during the OBD reading process, turn off ignition and read again.
If a missing/broken file burns the transmission computer, you are allowed to reset data via boot mode.
Boot mode: 
Strongly recommend to use the switch board to enable power automactic off/on.
switch-board
DQ500 Read/Write:
Directly connect KTMFlash with transmission computer. Manually turn on/off power by controlling 15 PIN J2534.  The second gear should always be on.
Read/Write VL300/V30 via BSL:
Need to drill a hole on the transsmision computer to add a 1Ω resister to GND with a probe. Then connect to k-line. (Strongly recommed to use a switch board as well.)
Location to drill a hole shown as picture below.
ktmflash-vag-dsg-1

ktmflash-vag-dsg-2
Connection diagram:
ktmflash-vag-dsg-3
Red- +12V
Black – GND
Yellow – CAN-HIGH
Blue- CAN-LOW
ktmflash-vag-dsg-4
KTMFlash (pcmflash software) read DQ200/DQ250 in action:
Read DQ200
ktmflash-vag-dsg-dq200-1

ktmflash-vag-dsg-dq200-2

ktmflash-vag-dsg-dq200-3
Read DQ250
ktmflash-vag-dsg-dq250-1

ktmflash-vag-dsg-dq250-2

ktmflash-vag-dsg-dq250-3

ktmflash-vag-dsg-dq250-4
Read Audi C7 DQ381
ktmflash-vag-dsg-vl381-1

ktmflash-vag-dsg-vl381-2

ktmflash-vag-dsg-vl381-3

Share This Post

site by bcz